|
|
|
|
|
Eifion Jewell, Simon Hamblyn, Tim Claypole and David Gethin
A comprehensive experimental investigation has been carried out into the role of film thickness variation and silver material formulation on printing capability in the screen printing process. A full factorial experiment was carried out where two formula...
ver más
|
|
|
|
|
|
|
|
|
|
|
Xue Qi, Heebo Ha, Byungil Hwang and Sooman Lim
Printing technology enables not only high-volume, multipurpose, low-impact, low-cost manufacturing, but also the introduction of flexible electronic devices, such as displays, actuators, and sensors, to a wide range of consumer markets. Consequently, in ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Caigui Yang, Zhiqiang Fang, Honglong Ning, Ruiqiang Tao, Jianqiu Chen, Yicong Zhou, Zeke Zheng, Rihui Yao, Lei Wang, Junbiao Peng and Yongsheng Song
Recently, amorphous indium-gallium-zinc-oxide thin film transistors (a-IGZO TFTs) with inkjet printing silver source/drain electrodes have attracted great attention, especially for large area and flexible electronics applications. The silver ink could be...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hsuan-Ling Kao, Cheng-Lin Cho, Li-Chun Chang, Chun-Bing Chen, Wen-Hung Chung and Yun-Chen Tsai
A fully inkjet-printed strain sensor based on carbon nanotubes (CNTs) was fabricated in this study for microstrain and microcrack detection. Carbon nanotubes and silver films were used as the sensing layer and conductive layer, respectively. Inkjet-print...
ver más
|
|
|
|
|
|
|
|
|
|
|
Redwan Ahmad, Mariia Zhuldybina, Xavier Ropagnol, Ngoc Duc Trinh, Chloé Bois, Juan Schneider and François Blanchard
We designed and fabricated a terahertz (THz) frequency selective surface (FSS) based on two distinct additive manufacturing technologies, namely, printable electronics (PE) and three-dimensional (3D) printing. Silver nanoparticle ink was printed on a pol...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hyunkyoo Kang, Seokjin Kim, Jaehak Shin and Sunglim Ko
Inkjet-printed strain gauges on flexible substrates have recently been investigated for biomedical motion detection as well as the monitoring of structural deformation. This study performed a topographical analysis of an inkjet-printed strain gauge const...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sun Chan, David Cryer and Roger I. Price
A 3D-printed metal solid target using additive manufacturing process is a cost-effective production solution to complex and intricate target design. The initial proof-of-concept prototype solid target holder was 3D-printed in cast alloy, Al?7Si?0.6Mg (A3...
ver más
|
|
|
|
|
|
|
|
|
|
|
Egor A. Danilov, Mikhail Veretennikov, Maria Dronova, Timofey Kalyakin, Andrey A. Stepashkin, Victor V. Tcherdyntsev and Vladimir Samoilov
Electrical and optical properties of graphene/silver nanoparticles hybrid suspensions intended for use in inkjet printing technologies were studied. Few-layered graphene particles were manufactured via a direct ultrasonic-assisted liquid-phase exfoliatio...
ver más
|
|
|
|
|
|
|
|
|
|
|
Irina Petukhova,Irina Shekina
Pág. 35 - 40
Teaching computer literacy to the elderly, as well as the very participation of this age group in Internet communities, is a ?fashionable? leisure practice, although not accessible to everyone. In our study, we focus on the study of several areas of netw...
ver más
|
|
|
|
|
|
|
|
|
|
|
Giovanni Gugliandolo, Antonino Quattrocchi, Giuseppe Campobello, Giovanni Crupi and Nicola Donato
In recent years, inkjet printing has emerged as a promising advanced fabrication technology in the field of electronics, offering remarkable advantages in terms of cost-effectiveness, design flexibility, and rapid prototyping. For these reasons, inkjet p...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ceren Yüce, Markus König and Norbert Willenbacher
Further strong growth of solar energy conversion based on PV (photovoltaic) technology requires constant improvement to increase solar cell efficiency. The challenge in front-side metallization of Si-solar cells is to print uniform fine lines with a high...
ver más
|
|
|
|
|
|
|
|
|
|
|
C. G. Moura, H. Dinis, O. Carvalho, P. M. Mendes, R. M. Nascimento and F. S. Silva
The use of Yttria-stabilized tetragonal zirconia polycrystals (Y-TZP) in medicine has rapidly expanded over the past decade, driven by its advantageous properties, showing potential to overcome titanium alloy in implant fabrication. The release of metal ...
ver más
|
|
|
|
|
|