|
|
|
Xoan F. Sánchez-Romate, Alberto Jiménez-Suárez, María Sánchez, Silvia G. Prolongo, Alfredo Güemes and Alejandro Ureña
Structural Health Monitoring of novel carbon nanotube doped adhesive joints under aging conditions.
|
|
|
|
|
|
|
Toru Nikaido, Rena Takahashi, Meu Ariyoshi, Alireza Sadr and Junji Tagami
It has been proposed that a resin coating can serve as a means to protect dental structure after preparation of the tooth for indirect restorations, sealing the exposed dentin. The resin coating is applied on the cut surfaces immediately after tooth prep...
ver más
|
|
|
|
|
|
|
Haixiao Fang, Hongjian Zhao and Jining He
In this study, Ti/Cu multilayer film was deposited by magnetron sputtering and then nitrided at 800 and 900 °C in N2. The microstructure and wear performance were studied. The deposited Ti/Cu multilayer film mainly consisted of Ti and Cu phases. After ni...
ver más
|
|
|
|
|
|
|
Jan Tomastik, Radim Ctvrtlik, Martin Drab and Jan Manak
The scratch test, as probably the most widespread technique for assessment of the adhesive/cohesive properties of a film–substrate system, fully depends on reliable evaluation based on assessment of critical loads for systems’ failures. Tradi...
ver más
|
|
|
|
|
|
|
Zuli Mao and Li Yang
We report the synthesis of SiC/Si3N4 coatings on carbon/carbon composites via pack cementation and heat treatment with nitrogen gas, the latter of which improves the coating wear resistance. X-ray diffraction (XRD), scanning electron microscopy (SEM), en...
ver más
|
|
|
|
|
|
|
Sang-Hyub Lee, Se-Woo Yang, Eun-Suk Park, Ji-Young Hwang and Dai-Soo Lee
The adhesion between aluminum (Al) foil and cast polypropylene (CPP) film laminated with mixtures of amorphous- and crystalline-maleic anhydride-grafted ethylene-propylene-diene monomer (MAH-g-EPDM) rubbers and highly reactive polybutene (HRPB) as the ad...
ver más
|
|
|
|
|
|
|
Yandan Zhu, Mufu Yan, Quanli Zhang, Qiwen Wang and Hangyu Zhuo
To improve the surface wear resistance, plasma nitriding of the prefabricated Cu-Ti films on the C17200 Cu alloy is performed to investigate the effects of the composition of the Cu-Ti films on the microstructure and the mechanical properties of the modi...
ver más
|
|
|
|
|
|
|
Wan Izhan Nawawi, Raihan Zaharudin, Ahmad Zuliahani, Dyia Syaleyana Shukri, Tun Firdaus Azis and Zainab Razali
Immobilized TiO2 and immobilized TiO2-polyethylene glycol (TiO2/PEG) films have been prepared via brush coating method. The formulation of immobilized TiO2 film was prepared by mixing distilled water with P25, while the formulation containing P25 combine...
ver más
|
|
|
|
|
|
|
Fu Zhang, Xinyue Wang, Xiahua Cui, Yubo Qiu, Shuai Teng, Shaukat Ali and Sanling Fu
In order to improve the adhesive and passing performance of agricultural tracked vehicles under a non-structural environment, a theoretical design method of the structure of a bionic track pattern is proposed in this article. The Saanen goat is taken as ...
ver más
|
|
|
|
|
|
|
Yuriy Tsapko,Denys Zavialov,Olga Bondarenko,Nataliia Marchenco,Serhiy Mazurchuk,Oleksandra Horbachova
Pág. 37 - 43
The studies allowed manufacturing dead pine wood thermal insulation materials for the arrangement of premises. Raw materials for their production are wood fibers formed as flat boards. The mechanisms of the thermal insulation process during energy transf...
ver más
|
|
|
|
|
|
|
Ann Karakurkchi,Mykola Sakhnenko,Maryna Ved?,Iryna Yermolenko,Sergey Pavlenko,Vadym Yevsieiev,Yaroslav Pavlov,Vladislav Yemanov
Pág. 29 - 38
Approaches to the use of electrochemical coatings in surface treatment technologies are analyzed. It is shown that directed surface modification allows expanding the functional properties of the treated material, in particular, increasing the strength, w...
ver más
|
|
|
|