|
|
|
Yalei Bai and Donglei Wu
In daily operation, the flow state in the runner chamber of an axial flow pump is extremely complex, and the pressure pulsation caused by the vibration of the unit and the hydraulic excitation is also extremely complex. The pressure pulsation will also g...
ver más
|
|
|
|
|
|
|
Weihong Kong and You Li
The large reverse flow region of the rotor with a high advance ratio is an important factor that affects the performance improvement of helicopters. This paper examines the dynamic stall of the airfoil in the reverse flow region of the rotor to develop a...
ver más
|
|
|
|
|
|
|
Joseph Moubogha Moubogha, Gabriel Margalida, Pierric Joseph, Olivier Roussette and Antoine Dazin
Stall and surge are strong limitations in the operating range of compressors and thus one of the major limits of jet engine performance. A promising way to push the stability limit of compression machines is to inject a small amount of flow at the blade ...
ver más
|
|
|
|
|
|
|
Weidong Cao and Wei Li
The operating range of axial flow pumps is often constrained by the onset of rotating stall. An improved method using a double inlet nozzle to stabilize the performance curve is presented in the current study; a single inlet nozzle and three kinds of dou...
ver más
|
|
|
|
|
|
|
Jerzy A. Owczarek
This Technical Note calls attention to the fact that observed initiation of stall in an axial flow compressor can be explained by the pressure pulses reflecting between the stator and rotor blades. The phenomenon of reflection of pressure pulses between ...
ver más
|
|
|
|
|
|
|
|
Lance W. Traub and Mashaan P. Kaula
One of the most commonly implemented devices for stall control on wings and airfoils is a leading-edge slat. While functioning of slats at high Reynolds number is well documented, this is not the case at the low Reynolds numbers common for small unmanned...
ver más
|
|
|
|
|
|
|
Mohammad Akhlaghi and Yahya Azizi
In this paper, unsteady characteristics of a modified vaned-recessed casing treatment with 23.2% rotor blade tip axial chord exposure were studied numerically. The modifications to the traditional vaned-recessed casing treatments were composed of geometr...
ver más
|
|
|
|
|
|
|
Sandro Erne, Gernot Edinger, Anton Maly, Christian Bauer
Pág. 94 - 106
This work presents the assessment of the mean flow field and low frequency disturbances in the stay vane channel of a model pump turbine using transient numerical simulations and LDV-based measurements. The focus is laid on transient CFD simulations of c...
ver más
|
|
|
|
|
|
|
Marhamat Zeinali, Sarallah Abbasi, Abolfazl Hajizadeh Aghdam
Pág. 288 - 295
Commencement and development processes of unsteadiness, caused by blade row tip leakage flow in a low speed axial compressor, are investigated and results are presented in this paper. Analyses are based on results obtained through numerical simulation of...
ver más
|
|
|
|
|
|
|
Shiji Zhou, Shengfeng Zhao, Chuangxin Zhou, Yunfeng Wu, Hang Yuan and Xingen Lu
To explore the internal flow mechanism and improve the performance of a supersonic compressor, an efficient global optimization design method was developed for an axial flow compressor and applied in the optimization design of a prototype supersonic comp...
ver más
|
|
|
|
|
|
|
Yuqiang Wang, Zhe Wang, Xiangyu Song, Ling Bai, Mahmoud A. El-Emam and Ling Zhou
This paper focuses on investigating the stall phenomenon of a three-stage electrical submersible pump using numerical methods by examining the internal and external characteristics of the pump under design conditions and critical stall and deep stall con...
ver más
|
|
|
|
|
|
|
Shuli Hong, Jun Chi, Xin Xiang and Weiyu Lu
A centrifugal compressor of a micro turbine generator system is investigated by the theoretical model and numerical analysis to explore the characteristics of the tip leakage vortex as the centrifugal compressor approaches stall. The numerical simulation...
ver más
|
|
|
|
|
|
|
Mario Eck, Silvio Geist and Dieter Peitsch
Axial compressors in aero engines are prone to suffering a breakdown of orderly flow when operating at the peak of the pressure rise characteristic. The damaging potential of separated flows is why a safe distance has to be left between every possible op...
ver más
|
|
|
|
|
|
|
Hai Du, Hao Jiang, Zhangyi Yang, Haoyang Xia, Shuo Chen and Jifei Wu
The characteristic of delayed airfoil stalls caused by the bio-inspired Wavy Leading-Edges (WLEs) has attracted extensive attention. This paper investigated the effect of WLEs on the aerodynamic performance and flow topologies of the airfoil through wind...
ver más
|
|
|
|
|
|
|
Shuai Ma, Jun Hu, Xuegao Wang and Jiajia Ji
To make measurement of end-wall flow between blade rows in a compact multistage configuration possible, a miniature L-shaped five-hole probe was employed in this paper. This compact tip structure, realized by laser-printing instead of the conventional ma...
ver más
|
|
|
|
|
|
|
Xiangjun Li, Jiezhong Dong, Hua Chen and Huawei Lu
Nowadays, with the increase of the thrust-to-weight ratio of the aero engines, the high aerodynamic load has made corner separation an issue for axial compressors. The complex three-dimensional flow field makes it challenging to suppress the corner separ...
ver más
|
|
|
|
|
|
|
Nicolas Poujol, Martin Buisson, Pierre Duquesne and Isabelle Trébinjac
In centrifugal compressors, Mild Surge (MS) leads to unstable operation. Previous experimental work on a centrifugal compressor designed and built by Safran Helicopter Engines (SafranHE) showed that MS corresponds to the pulsation of an alternate stall p...
ver más
|
|
|
|
|
|
|
Alberto Baretter, Benjamin Godard, Pierric Joseph, Olivier Roussette, Francesco Romanò, Raphael Barrier and Antoine Dazin
On many occasions, fan or compressor stages have to face azimuthal flow distortion at inlet, which affects their performance and stability. These flow distortions can be caused by external events or by some particular geometrical features. The aim of thi...
ver más
|
|
|
|
|
|
|
Motoyuki Kawase and Aldo Rona
The tip leakage flow over the blades of an axial compressor rotor adversely affects the axial rotor efficiency and can determine the onset of tip leakage stall. The performance of a new casing treatment concept in the shape of an axisymmetric recirculati...
ver más
|
|
|
|